OK… The time has come to do some work . It’s a mess. I can’t find most of my tools. In my other post the garage was dry walled and painted. Now the heater is installed so we are good to go.
The heater is nicely tucked up in the corner. So now I know where I can install shelves and hang stuff. It’s time to organize and unpack. One of the things to do was install a shelve between the two upper cupboards.
Yes very good storage for stuff I don’t need every day. But it can’t be heavy because I need to lift it up there. Oh yes I’ve been busy..
I’ve built a new work bench. and look it’s messy already. The drill press and the vice (under blue towel) are mounted. And it’s painted too !
And more shelves and… I bought a 42 inch wide steel cabinet for my paints and whatever else I decide to put in there. All of this should take the pressure off the big shelves.
Important News:
I have sold the Kubota BX tractor. It will be gone from the garage latter today and that will give me tons more room.
Bye Bye to a good friend. But there is no more work for you.. I have a paved driveway and a new electric snow blower. It’s all part of the plan to lighten the load. And now … Say good bye to the two ATV’s and the Honda scooter.. wow got my space back ! However took the funds and bought and good ATV ..Newer… almost no work needed. 2013 Polaris.
Time to do some yard cleanup and make some changes.
During the move I had taken down the fence between the garage and the house. This made it easier to get stuff into the back of the house and put the outdoor stuff close to where it will stay. With intentions of turning the space between the garage and house into a parking area. Parking on the street for three vehicles is all we have right now so this will give us more parking. Always better to have the vehicles off the road.
This area ! It’s 16 ft wide .. and I’m moving the fence back 8 ft into the yard. This is what I’m currently working on.. One of the first jobs that we got done is the garden shed.
Tucked it nicely into the corner. This strip will be gravel and a place to park the utility trailer. The problem here was the ground level. It was up to and covering the vinyl siding. That’s just inviting problems for the garage . Notice the gas line on the far right. With the test gauge still there… it’s for the garage heater soon to be done. But wait ! Before the gas line could be done under the deck needed to be cleaned up. The gas meter is there.
Cleaning up under the deck… What a mess ! Make way for the gas line to the garage . You can see the trench in the above photo. It’s all done now and a load of gravel spread. All done by hand.. no room for the tractor.
Great place to NEATLY store stuff like the kayaks. This fence between the house and the neighbors needed to be replaced . One post and most of the wood pickets were rotten. Now that’s done back to the the BIG job… And this is how far I’ve got… to the end of August.
I have the new fence posts in the ground and the forms around them for a 16 inch wall. By digging down I was able to level the parking pad 16 ft out towards the street. That’s a big level parking pad.
Here’s the concrete work all done. A nice large step at the gate. Plus a concrete apron for the double gate opening to the parking pad beside the garage.
Here’s a different view of the parking pad.. And shows better how I came 8 ft into the yard. I have the metal for the fence now and I replaced the fence section on the north side of the deck.
Just over 5 ft high and never needs painting. Just need a bit more gravel inside the fence and we are done. Back to the parking pad…
I’m working on getting the slope to the sidewalk just right. The whole thing is 20 ft wide .. so it’s a double wide parking area. With a path from the stairs. I believe that pile is the last of the dirt and sod getting hauled away. And after some tweaking I got the slope good.
Time for a truck load of the road mix.. And to spread it evenly..
Poof done ! Now we are looking at this and thinking the sand and gravel is kinda .. dirty. So we called the pavers. And that means My part is done. So I started on the fence.
And here we have most of it done …just the double gate needs to be built, But I’ll wait till the pavement is done. They came the next day.. and in 5 hrs we had a very nice new driveway.
The crew had only a little prep work to do cause I had done most of it. The transition and slope is prefect. We’ll give it a few days to set up before parking on it. Meanwhile I have two more gates to build.
And there we have it. The best gates I’ve made yet. Six feet high and very little gaps. They open out so I can better access the back yard. And with that we are done .. The cats can use the yard and be safe. Next is cleaning up and organizing the garage. Which has it’s own post… Work on the garage
But now I have help! Brother in law is here from Winnipeg to give a hand. I’m now done most of the painting. Now we have some work to do that having help with it is great. Starting with the half wall in the kitchen.
This change needs to be done before the painter comes next week to paint the living room and kitchen. Adding 1 ft to the half wall is needed to have power outlets and back splash for the new lower cabinets that are happening here. So this was #1 on the list.
Week 4.. home stretch.. All the painting is done except for the computer room.
The plumbers have been and that work is done. New water conditioner, new sink and a new outside faucet. The yard shed is up and the garage is done …
There’s a lot more in there now.. So Brother in law is heading home and I can handle the last of the yard stuff. Movers are coming in six days.
Update : Mid August… Been so busy ..no time for updates. We are moved in and mostly set up. The garage is full.. as expected. But it all fits.
The poor garage had to swallow up the contents of the sea can, barn and the garage from Pinter dr… plus the two atvs and the Kubota BX.. it’s all in there now. In the house the furniture is all in place in the different rooms.
This is the set up for the family room. Still a bit of work to do. And the office has been wired and painted . New shelves and the fiber now comes in here.
Still needs the drop ceiling done. And it’s getting a new window. A work in progress. but not the living room all done except a few pictures.
Notice the one foot rise in the wall. Hard to tell it wasn’t always like that. Yes you are seeing a lot of the same color paint.. We bought too much so I was using it in the office too. And that turned out great. Our computer desk that we have had for ever fits. Nice to have high speed internet and TV again.
Since we are so good at moving …let’s try it one more time. One LAST time. However this is a good move… let me explain. This spring we listed the house for sale.. So with all the reno’s we did and the market improving …why not see what happens. Well nothing happened for two months ! Then on the last day of the listing along comes an offer and it’s a good offer… Darn we were all set to stay. During that two months we were searching all the possible homes available. Some sold before we could make an offer. And lot’s of them were a not for us.. (rightfully fussy). But now we have a sale on ours.. The pressure is on. So then we started looking at homes that didn’t tick all the boxes but most. And everything needed to be considered. And this one was the best deal !
Say Hello to 35 Park Place ..
You know the saying: Location Location.. This is it for Drumheller. Even last year when we were looking and not really familiar with the neighborhoods This was the part of town that we were drawn to. It’s called Midland and it’s on the north west side of town. On the road to the Museum. And that road can be busy during summer.. But not by trucks just the tourists. This house is away from that road and on a dead end drive. Yup I’m holding on to the quiet that I like. Also it’s on the edge of the Midland Provincial Park, which is the home of the Royal Tyrell Museum. AND we will now benefit from full city services, like paved roads and Fiber internet and tv.. Yes this is a smaller lot. Just a regular size, but it’s all done for us and with a fully fenced back yard.
Two decks …one is all screened in…
We like ! But let’s talk about what’s not seen in these photos.. just a peek on the right side of the house photo. This !
Wow ! 26 x 24 insulated ( soon to be finished and heated ) GARAGE. Oh baby … I’ll make good use of this. Would be better if it was attached to the house…but we couldn’t have everything. The house has some interesting things.. Like the sunken living room.
Different yes.. Very much the same size as our current home. Three bedrooms , two bathrooms. The basement has a big utility room, a family room and a nice room for computers and hobbies. All needing no renovations just a little paint and we want to remove the only carpet in the house in the family room. We also want to eventually change out the wood fireplace for a gas one. SO what makes this move worth it. I’ll share the list;
# 1 Less property to look after.. I’m selling the riding mover for a electric one.
# 2 A big heated garage for me..
# 3 House has a newer high efficient furnace AND central AC.
# 4 The wiring and plumbing is great no changes needed
# 5 Telus Pure Fiber is in the house.
# 6 The Kitchen is good and we are only adding one extra cabinet plus some new appliances.
#7 The three bedrooms are bigger and we can use all three.
#8 Storage ! this house has way more.. There is a 4 ft high crawl space under the living room.. tons of room .
That’s enough reasons for us.. We are looking forward to this move.. One other thing that makes this good for us is the deal we made to purchase the house. The renter would be moving out at the end of June.. Our date for the actual purchase is Aug 8 th. I’m writing this at the first part of July.. In a few days we have the keys to the house and as part of the agreement will have from now ( one month ahead) to clean , paint, finish the garage, change the floor in the family room. We are having a water conditioner installed. Set up the new garden shed. AND move some of our things in as there is room.. All before the movers do the furniture on Aug 6 th. That’s a huge advantage for us.. All this will mean we are settled in quickly. Soon we will be very busy.. But I’ll try to take the time to continue this post..
Ok ..,.It’s the 8th of July and we are in the house it’s ours to do the fixing up needed. We have a month before moving day. So every morning we head to 35 park pl to do our list of things. And it’s a long list. Today the crew came and started dry walling the garage. The plumber came to access what needs to be done. And our cabinet guy came to measure for the new cabinet for the kitchen.
This wall which is currently doing nothing to help the kitchen will be put to work. Six feet of lower cabinets will be here. Providing lots of additional storage and counter top space. I will be raising the wall a foot so there can be power outlets and stuff won’t fall off the back of the counter.
And of coarse finishing the garage speaks for it’s self.. Wait till you see it done. Then I can start moving my shop stuff in.
This is one of the spare rooms upstairs. We are re painting all the upstairs except the two bathrooms. This room will be two tone gray .. the blue is too much. The other spare room will be a neutral taupe paint. Interesting checker plate wall paper. The family room in the basement is getting some love too.. We don’t want carpet so we removed it and put it in the crawl space. New laminate flooring for that room and some paint. We are now a week into the work and there is lots of progress. The room pictured above is now finished.
Looks great.. As well I finished the second spare bedroom which had green painted walls. It looked like this..
But no more..
The color is called “latte” don’t know who’s latte.. but it’s very neutral. The family room got a coat of paint today as well. But something went wrong with the paint and it changed color as I progressed. I’ll repaint and then take a photo.
A couple years back I bought a “sea slipper” tri- hull boat. And it’s a heavy beast.. It came with us on our move to Drumheller … and now it needs a trailer.
Cool hull design.. Should be very stable.
In very good shape. It was a rental boat at a popular fishing lake near Vernon. It made the trip here on one of my trailers that I picked up also a few years back.
That’s all good …but the boat is upside down.. I need a proper boat trailer not a flat deck. Solution ! build one by modifying the flat deck frame.
When I got the trailer it looked like this.. I took the sides off and below is what it looks like now..
Has new 12 ” wheels , the lights work.. BUT I will be making some changes! And that’s what I got up to today.. First I ripped the deck off and tossed it. then I parked it on stands in front of the garage so I have access to tools.
And this is what we have.. Too much metal ! Nothing a zip cut can’t fix. I only need the middle part.
There ! I believe I removed 100 lbs of steel. don’t need it . Now I’m planning how to extend the tongue an extra 2 ft out front. As well I would like to keep the tilt feature. So I moved the hinge point for the tilt 24 inches forward. this was the way to extend the tongue so that the boat would not be too close to the hitch and keep the tilt.
You can see where it was over the axle.. A good place for tilt balance… But a boat trailer works different. I’m re- using some the the channel steel from the extra pieces to add a vee nose out front.
This brings the saddle for the tilt lock pin closer to where you can reach it. I’m having problems with my welder … It’s not hot enough to really penetrate the thicker steel.. So I’ll be bolting everything. A bit of extra work but I don’t want trouble later. In fact it did not hold at all. So I will have to think of a way to bolt these two parts together.
And here’s something to fix.. The angle pieces must be different lengths.. Cause things are not meeting in the middle. I measure from the hubs to the hitch from both sides. This is how you get a trailer that tracks straight.. I will fix this.
Here’s some more bolts for extra insurance. This is one of two places that take the weight of the pull going down the road. I’m have to say that’s important ! Yup it’s important. So at this point I want to put the boat on the trailer and fit the bunks and the winch stand.
Yup it’s a good fit.. Now I need to do some fitting .. I started with the bunks.. Easy to make. Three foot 2 x 4 covered with boat carpeting.
And large angle brackets too. Getting the right height was tricky. I’ll mount them after painting. Then I need a winch mount .. Lot’s of work getting this right. And finding metal that would work.
But I got it.. ! Sturdy and the winch strap passes through straight to the bow fitting. Now to re work the tilt lock so only bolts are used.
Well because we are moving ..with no place to park extra stuff.. I have sold the boat on the unfinished trailer with the 3.5 Merc motor.
This is a bad gash in the top of the speedo pod. I’m thinking chainsaw.. Can’t for the life of me figure out how one would do such a thing. But I’ve had more than my share of head scratches. Look how faded the yellow is.. I’ve tried the wet sanding method.. But this goes deep. I have a solution for that gash I’ll show later.
With the plastics off everything got a good bath. Now I can thoroughly inspect the drive line and suspension. And I found some loose stuff, and some things that need replacing.
Like the front brake pads. This one was beyond wore out ! Tie rod ends are toast as well …So I have some parts coming. While waiting I started work on a boat trailer . And I did some work on the bush guard and winch.
Cleaned up the winch, breathed new life into the fair- lead rollers. Some were not turning at all. And here’s what the yellow top of the light pod looks like now.
The gash was filled with epoxy and I used the heat gun method to deal with the fading. Not perfect but does work 50% sorta thing.. Once I get my parts I’ll service the front hubs, bleed the brakes and tighten anything I find needs it. Then I’ll move on to the rear wheels. The brakes are now working great and a new bearing installed on the left rear hub. We tried and tried the start the quad.. no luck … what’s up it was running.. Best thing to do is park it and wait till I’m in the new shop.. And then do some more tinkering. It’s a spark issue..
Oct 2022:
Well I’ve had the time to set the shop up .. And evaluate what I’m doing this winter. I’ve decided not to tinker with the quads. I want to clean out the whole shop and work on my Avalanche. So I have sold both to a nice guy who is a mechanic.. I will be replacing both with a new one … Here’s the start of a new post:
The price was right and it came with extra parts quad.
It runs …it drives .. But there are a few issues, like no brakes, and some electrical gremlins. Probably bad connections. We fix. The plastics are faded. And the bush bar is a little bent. The factory winch works, and the tires are good. Someday I’ll bring it in the garage and look after these things.. What I really needed was the wiring harness that the parts one had. That harness with / should bring my 2005 back from the dead.
Here’s the parts frame. I’ve since removed the wheels , wiring and the handle bar. And I put it on a pallet so I can move it easily.
So this 2004 yellow 400 is just to hold me over till I get the 2005 going.. I’m not sure when that will be, hope it happens this year.. So I’m going to put some effort into the yellow 2004 one to bring it up to my standards . Here’s what I see is needed..
Wiring: bad grounds and possible corroded connections. I noticed the head lights are dim. and the kill switch isn’t working.
Check brakes, hubs and all bushings and bearings: Just cause !
Plastics: I’ll remove all the plastics and repair and polish them.. Make it pretty again. Repaint the rims too. And fix the bush bar.
And with the garage all organized and clean.. In comes the 400 to look after those things.. First thing remove the front rack and the bush guard and front trim. Need to get a good look at the wiring.. I also removed the handle bars so I could tweak the the mounting plate a tad. The bars and nacile had a bit of a tilt to the left.
While the guard was off …why not give it some fresh paint and bang the kinks out.
I was able to find the bad wire and now it starts and stops with the key.. Cleaned a lot of connections too. Next I need to remove all the plastics.. this is were I find the broken bits.. But let’s start a new page
Getting warm out so lets see what we can do. First off I wasn’t happy with some of the work the detail guy did.. Carpets are good and the headliner too. But he dropped the ball on the seats.. So I gave them another go.. !
Just got to scrub a little harder.. Then I used some leather conditioner / protector. Nice… I then used the decal kit for the HVAC controls..
Again… Nicer.. Once I get all the bits for the stereo install I can get that done.
I did find the passenger side running board at a wrecking yard in Calgary. It’s a good thing Albert-in’s crash a lot.
Also grabbed a good driver’s side tail light. The other one on the vehicle is cracked. These won’t be changed till the painting is done. And speaking of that…. I’m getting quotes from small body shops. We will see how that goes..
Update: May 2022
I now have a guy who will do all the body work and painting . Local too. He’s got the parts I bought..and soon the Avalanche too.
Wow six months has passed by in December.. It’s now the end of January and I’m looking back at those first months here in the new house and new community. It was a cold winter..
However !
Spring 2022.
I’m making a new post for 2022.. Because things are changing for us.
Referring to the body of coarse… after having a close look and assessing whats needed and what could be fixed. I need to replace both rear doors, both front fenders.. and maybe the front bumper. Also I need a right side running board. These are where the most damage is. Found a body shop in Strathmore that was selling the body parts off of a 2008 Avalanche. $100 bucks each for the doors and fenders. Wow my quote from the wreckers was $400 ea for doors.
I also got a white front bumper and the bottom air dam that finishes it. That will fix the worst goober on the right front corner.
This ! Wonder what they hit.. ? The right side fender and the front bumper cover will fix this…
The left fender will make this disappear. Unfortunately I can’t get the same color parts.. So some painting will be needed.
You know I don’t really need the pearl paint.. It’s very expensive. If I just settle for a nice off white one step paint I could save a lot and do the whole truck. For now I’m stopping the rust, and sealing it. And for now it’s too cold for any body work. SOOO I’m concentrating on the interior. As I said I’m having the inside professionally cleaned. That is happening today and tomorrow we will see how that turned out. I have ordered the bit and pieces to repair the few things not right inside the avalanche. Starting with the dash.. Wouldn’t you know it one of the cool things you can get is a new dash cover.
Glues right over the old one. easy fix! The other cool thing I found was a kit for fixing the heater controls. The typical scratched off finish on the most used buttons.
would ya look at that.. even if you found a Hvac control at a wrecker it would still look like mine and cost more than the twenty bucks for these.
Back from the detailing shop..
Well… it’s better .. he did a good job on the carpets.. But could have got the seats cleaner.
At least it smells nice.. More bits and pieces are arriving soon. The console lid, the dash cover. And a new stereo system.. that will give me the backup camera. I found out what the 12v plug in the console was for.. it powers up the two DVD players in the head rests.. Hmmm don’t need those so I left it unplugged.
The new stereo arrived today..
This is a media player. It uses the Android operating system. It does a lot of things, basically anything my phone does. All I need still is the dash install kit and the GM interface module. And some warmer weather. This will bring the tech in this 13 year old truck up to date. And the “Loaded” term will apply. Also had an inspection done and only found two small things to fix. That will be done next week with a service. I’m not worrying about the ride control anytime soon.. The Avalanche rides nice and the nagging message is not happening any more. The weather is warming up….SOOO let’s start a new page.
It’s the one on the right.. Yes I have three. Yes the oldest one has the least Kms. But those two will be gone soon. So time for an upgrade for me. A bit newer and a whole lot more fancier. Like one grill away from being a Cadillac, but without the expensive parts ! Now for some Avalanche history.. The last year Chev made Avalanche’s was 2013. This one is a 2009, and there is only a few changes in those last years. New this one would have sold for big bucks… on the plus side of 50 thousand. The LTZ model is top of the line, and the only two things missing from this one is Nav and the rear camera. So it’s definitely what you call “loaded”. ( I’m adding those)
Hard to tell but this is the pearl white paint. Which is classier than just white. From the factory it would have 20 inch chrome wheels , But these are new after market 20 ” “Worx” rims and new Michelin winter tires. That’s a bonus for me, and so was the new windshield.
It’s nice to see a bumper that is not bent, ya some paint chip and scratches but not bent.. The parking sensors work ! and the trailer plug too. The rest… well nobody ever cleaned the interior. And something very heavy was put on the dash and cracked it. But no other damage inside. Lets have a look , and consider these the “before ” pictures.
Light grey leather seats. Dirty but still in good condition. These are heated and cooled ! The driver’s seat is the one that takes a lickin… And there is some cracks on the side, but not on the seat. They are comfy too.
You can see the cracks… but they are not bad. These seats are 8 way power..both sides.
The rear seats have probably seen some kid activity, but survived nicely. I tumbled the seats and opened the mid-gate, it’s all good. The Avalanche has a date with the auto detail shop this week.. Should see a big difference. I’m going to interrupt here and say that this Avalanche drives very nice. Brakes are great …lots of power and good on gas too. It was a two hour drive back from Calgary yesterday and cruising at 106 kph I got 10.6 liters / 100 km. Not too bad! Plus it goes down the road straight. It’s a pleasure to drive. AND it has 285,000 km on the old odo. Alberta is like that.. everything has high kms.
Yes two DVD players ! Crazy eh.. They will most likely never get used.
So lets talk about the elephant in the room…the reason I paid six grand for a Ten thousand dollar truck.. THE BODY ! yes That’s where the work will be. Oh and I want to say don’t waste your money on one of those electronic rust inhibitor’s. There’s one installed on this Avalanche from new I presume …I found it.
They don’t work and this truck proves it.. RUSTY you bet. Ya it’s Alberta and they use lots of salt on the roads…but if you wash it ..keep wax on it should last longer than 13 years.
This is the drivers side rear fender. The other side is bad, and bottom of the doors and other places. So that’s a bit of work.. Then there’s other body stuff…
Like dents and scratches… Lots. So I’ll have to figure out what to do. The Avalanche is worth making nice. As far as the mechanical end of things all I’m aware of are the air ride system not working. And the two functions on the shift leaver are not working..They are: tow/haul mode and the manual shift button. Could be a bad wire. As for the air ride… After 13 years and 285,000 kms one should not expect that to work.. They were prone to failure. The fix is to change over to regular shocks and remove the compressor and install the delete kit on the wiring so the warning goes away. I’ll be surprised if there is other problem. Here’s a video.
Got a new plastic welding kit I’m dying to try out. However the welder uses butane… lots of butane. So I’m not super impressed.. But I can use the mesh and the rods. I have a cheap soldering gun with a flat shoe …and that works great.
Here’s the worst crack. Front fender …left side. I use the heat gun to soften the plastic and re – align the crack. Then weld the backside to make it strong.
Then weld the good side.. but it never comes out perfect with colored plastic. But it’s repaired and strong . This process works very good with the black plastic parts. When melting the PE plastic some of it evaporates into the air.. So it’s necessary to ad more plastic . Hard to do when it’s a color.
Here’s a bad one on the foot well. Same process but looks much better. The foot wells take a beating. Even if you are careful…
There is the same crack on the other foot well too. And a crack on the front bumper. All easy to fix. However lots of work needed on the rear fenders.
Two of the tabs under the seat were broken off. These are the front ones.. of the six along the upper frame. When these broke it allowed the plastic to get too close to the exhaust pipe and melted the broken parts.. I had to re construct some parts..
I use paper clips embedded in the plastic. It’s not pretty but works. And it is under the seat so no problem. That’s about it for repairing plastic parts. Finally I’m trying different ways of polishing out some of the scratches.
Here I tried wet sanding with very fine grit. works but leaves a dull finish. Power polishing with cut polish could bring the shine back. This is much the same as restoring headlights. One thing for sure it gets the years of grime off.
As a final step I use this ultra protectant. Looks new. But I haven’t dealt with the scratches on this yet.. So you know I’ll make the body parts nice again.. And I may just see about making my own side panels too. Some of the parts may take a while to come.. So I’m going to start a third page on the ATVs that I have had, fixed and rode. PAGE 3 My ATV history..
I’ve been working away since the finishing of the kitchen. Once the plumbing was all done and the last of the framing.. I was able to put up some drywall with the help from Brother Scott.
And this is where we are.. flooring is in . then the shower stall had to be installed.
Done ! Took a whole day to do this part.. some tweaking needed. But it looks great. Then the drywall is finished.. that covers the attachment flanges. We are ready for the taping now. The flooring was done before the shower because I wanted the flooring to go under the shower base. The floor is a new product. No glue vinyl sheeting.. Thick and water proof.. just like vinyl planks but no seams. Notice the upstairs toilet drain is gone from this picture. The modification done by the plumbers worked out perfect.
My Son has Come and taped and filled all the drywall. And today I sanded cleaned and primed the room.
Two more days and the painting will be done. And there’s more work after that.
Painting done ! and the trim is in too. Lights and the vent cover done ! And today I put the toilet back.
Vanity next… then maybe the door..
All DONE !
Skipped taking photos.. Sorry… But the important thing is … I’m finished. And we are having showers and using the bathroom.
This project turned out great. Careful planning and quality components makes the difference.. We love the shower. The vanity has lots of storage and counter room. The powered mirror is just cool.
Thoughtful things like LED lights (shower too) and coat hooks for the towels. I made a short video to point out the changes from the old bathroom..
And that concludes this project.. Taking the winter off renovations. I will be out in the garage fixing up my new Polaris quad. Check in on that HERE.
But the photo is the exact same as the one I found .. the front plastics are off mine, but I have them. Soon the reno’s to the house that need doing will be finished. And in the yard there’s nothing to do but clean snow.. ( if it snows). The garage is keeping a nice temperature.. so ya I can work out there. This popped up for sale and I jumped on it. $600. for a fixer quad that is my favorite model and my favorite color ! Dam right. This one was listed as a 2004… but clearly not.. Right above the Vin it says a manufacture date of 02/04/2005. Even the key tag says 2005. Bought in Red Deer. A bit of research tells me that this is an early release of the new Sportsman models. A body style that went right through to 2011. I believe it’s the first years that you will see EFI as an option. Plus the new shape for the head lights, and a trunk under the front rack. If it says HO it’s still got a carburetor, like this one.
Not as pretty as the top picture.. But that will change.
Here’s what I know:
It wasn’t crashed…nothing is bent or damaged to suggest it was. The motor and drive line is fine. I can’t start it because the problems are electrical. But the motor turns over nicely. There’s oil in the motor and coolant in the rad.. can’t see any leaks. The plastics have a few cracks in the typical places. Nothing that I can’t fix. However we are missing the two side covers.
The tires are factory Polaris and not cracked and still holding air! Wow. Even the rims aren’t bent. I’m certain there will be things like bearings and brakes / bushings that will need attention, but not worried. what is needed is repairs to the wiring harness. That will solve the problems that I will explain later. For now I’m giving it a bath and storing it until I clean up the garage and finish in the house.
It’s full on December now. The work in the house is done and Winter is here …maybe not officially, but it’s snowy and cold. I’m making room in the garage for the Polaris. I have one of the missing parts , the CDI. The surepower ECM is on order and who knows when that will show up. Those two things will get the electrical system up and running.
Here it is ! In the shop and on the table. Still waiting for the ECM.. but I’ll remove the rear plastics. Makes it easy to get at things.. And they need cleaning and repairing too.
Wow…no damage to the frame. Everything is straight. I have found one broken wire and the left front brake caliper is hanging from a wire !! It looks to be ok just missing the bolts to hold it on.. Fairly sure that this quad was stored outside..cause it’s dirty. But there’s other things needed… Here’s a list …and this could grow.
New CDI : I’ve got it now
New ECM On Order
New carburetor, Got a new one cause I can’t get the float bowl off and they are cheap..
New rear brake Master, old one looks like it leaked.
New choke cable, Old one broken
Battery, later when everything works
New Fuel pump. On Order, Again cheap so why not.
All three filters needing changed, need to order them
As well.. I’m going to replace all four wheel bearings. Change the oil. While I wait for parts.. I’m going to clean and repair the plastic body parts. So we have some Plastic Welding to do… Page 2
And being installed .. All the base cabinets are in place now.. And a few of the uppers too..
Enough to tell me how much room on either side of the window. And whether my wire for the light was in the right place.. So far everything looks good.
Well here’s progress.. All the cabinets are installed and the crown molding done. It’s going to take another day to build the counter tops ..
A different view. We have more cupboard space now.
Here’s the first peek at the counter tops.. We like ! getting closer to the finish. Also the new stove is installed.
All Done !
And she’s moved back in.. Just the back splash tiles to choose and install.
A Few improvements… Cupboards and sink are now centered under window. New sink but kept the faucet… in works fine. Dimmable pendant light too. All the plumbing under the sink is new and improved.
More counter space. The dishwasher fits better so it’s very quiet now.
Garbage and recycle bins ! We had this in GF kitchen.. All the drawers are soft close.
In the old kitchen we moved the island from the middle to this position. Now it’s permanent with a one piece top.. and full height counter. The upper cabinets are higher to accommodate taller appliances. Extra outlets for charging stuff.
We had him do open shelves on this side… works for us.
We Love the new kitchen !
Now we do a back splash.. Carefully. Found the perfect tile right away .. Glass tiles with the odd aluminum one. We like it. This did not add any color, but that maybe a good thing .
It still adds some “pizazz” to the look. Very little cutting with the one inch tiles. But lots of grout ! 25 lbs to be exact. But it’s done and I can move on back to the downstairs bathroom. More pics:
She’s adding color with things on the counter and a red shade on the pendant light.
We used aluminum trim along the counter and where the tiles end on the wall.
