All posts by Rob

1973 Boler Trailer #2 the Frame

Oct 20 th  2017:

The Frame:

Yesterday I started the process of lifting the body off the frame..  Not too hard to do…   I’m working alone.  Just need a floor jack and beams..  After taking out the rusty screws.  It started raining heavily so I had to quit.    Today I’m back at it…

Had to remove the wheels so I could lower the frame more to clear the wheel wells.  So I put two 12 ft 4×4’s under the frame and pulled it out with the tractor..  All went well till I bumped one of the jack stands and the body almost fell to the ground..  But I sorted that out and ..  the frame came out and the new wheels went on.   One of the old wheels had a leak..

And there you have it… one SAD boler frame.  Yes it’s light..  but it’s very flimsy too.   Never mind the rust..  it’s cracked behind the left wheel…

Apparently this is common..  and it’s only one of the reasons why you want a new frame.  Usually the tongue has broken too and someone fixed that..  wow

Look at that ! they even jammed a piece of wood in there..   Let’s just say that this was not a “road worthy” frame..  and build a new one.   However first thing I want to do is construct a cradle for the body so it won’t have to sit on those jack stands any more.

Done!  I built it to hold the floor and the two ends.. My wheels are a bit wimpy but it’s all I got .. and they should help when I need to move it into the shop..   Now I stare at the frame and wonder where to start.  Some have built the new frame on top of the old one..  so as to get things aligned properly.   One thing I need to figure out is just how different the suspension will be.   The factory axles are Dexter Torflex.  And still available..  but costly to ship.  I bought the ones from Princess Auto..  made by the same company but they say 22 degree angle..  and the boler axle should be 10 degrees up and pointing forward..  A strange thing for sure.. but successful.  However the old axle IS the same as the new one at 22degrees.  Soooo I will flip the new ones ( they don’t say you can’t) and I will mount them an inch lower..   not much of a gain in height.. but still something.

Here’s the old and new..  for comparison..  The mounts are different ..but then the whole frame will be anyway.

One thing for sure ..this sag won’t be there !  That’s the new frame tube on top..  I’m kicking the old frame outside .. and cleaning up the new pieces..  everything is measured and the plans are drawn.   Here’s the first frame video…

Well I did kick the old frame out and made a jig on my saw horses to build the new frame..

The debate still goes on which way to mount the axles..  I’m tending to favor the rear configuration..  it will lift the trailer by 4 inches.. but I’m thinking that’s good.. cause I saw damage to the old frame from hitting things.  There was about 8 inches of clearance under the trailer.

Oct 22 2018:    I’ve decided to have the arms up and leading the axle.  And for a bit of extra height I’m adding a 1- 1/2 ” block between the frame and the axle.  I should be within 1 – 2 inches of the factory height.  This makes the door sill proper height.. you won’t need a step.  And that’s the way boler’s should be.

I now have my four cross pieces welded in place .. That’s four more than the old frame had.  The frame has been squared and corner braces added

The C – channel I used is from the Tent Trailer frame… light but strong.  I’m cutting the tubes to build up the 6 ” drop for the floor pan.  but since I’m working upside down it’s up…

I will cut the door opening after I have the frame braced.  Oh..  and the old frame is no more.. I cut it up to use some of the better pieces.  Would have been nice to keep it intact so I could show a side by side comparison..  but I don’t want to buy metal.. ya I’m a bit cheep.  Re-use and Re -cycle.. that’s the way I roll.

It’s coming along nicely..  There’s the door opening.  Used some bits from the old frame for this too.    Lot’s of welding going on here..

Got to have a place for the propane tanks..  And a battery in front of that.  Plus all this helps brace the frame.  The down side is the weight..  I plan on weighing it when I’m done..  and I expect a few hundred pounds more.  The up side is that this frame won’t need the body for support..  So the body is simply carried.

Here’s my new rear bumper..  it’s a work of art using pieces from the old frame.   Also it’s longer to protect the width of the trailer.  still needs a spare tire mount and the rear stabilizer jacks will be mounted too.  I will make this slide into the frame and bolt in place.  If I welded it that would make it harder to roll the frame under the body.

Oct 30 th 2017:     It’s looking like I’ll finish the frame earlier then I thought.   I got all the welding done.. cleaned up … and painted the bottom of the frame today..

Here’s the axles on..  and the two supports for the floor..

And now most of it is shiny black.  I turned the heat up to dry the paint better too.   Then I thought of a way to estimate the weight of the old frame. ..  by weighing the bits.   I estimate it to be 230 lbs.  + / – 30 lbs.   But at least I will know how much heavier the new frame is.

Nov 1 2017:    Well I rolled the frame out of the shop.. parked it next to the body..  I’m so nervous thinking I got the sizes wrong..  But it looks like a fit .  I want to take it and weigh it to see just how much heavier it ended up being.

And off to the scales and the landfill.   And wouldn’t you know it !  Lighter than expected !   330 lbs on the nose.   That’s approximately 100 lbs more than the old rusty frame.   Right on target..   I’ve still working on the rear bumper.. but the frame will stay outside now..  Like any good trailer.. :).

It’s done now on to the   BODY #3

 

 

1973 Boler Trailer…

This Post will have 7 pages: 

Introduction:

This summer a few of us were “talking projects”..  and what was worth the time and money.  The boler trailer always topped the list.  I said I should just do RV’s .. because I have lots of parts and a resource for new parts.  Well I bought one..  cheap enough to spend some bucks on it.  First I need to get the LeSharo RV running before starting on the boler.  And then I park it till spring.  but let’s get the blog going anyway.

And this is mine..  a bit of a mess.  been stored for many many years.  But it’s mostly there.  It will likely need work on the frame first..  and then the body has way too many holes..   I plan to strip it down to the shell and start over.. The list of things to do is long..  however this trailer is still in good condition for it’s year.  And so we begin..  with a video..

There’s a few things I forgot in the video..  like new suspension as well as wheels..  So it’s going to be like pulling a new trailer.  Plus this is like a blank slate for colors and décor.  We are already talking about those things..  And I’m thinking of ways to incorporate some of the parts I have.  Also how to bring it up to date with things like LED lighting,  power monitoring and better fabrics.  All while trying to keep a bit of “nostalgic” ness to it.  But the frame on these is always been the weak part.  So if it’s never been replaced then you have to start there.

Frame: (problems under there)

How fortunate that there are lots of folks who have built new frames ..and shared their designs on the net.  So I’m taking their ideas… and my ideas, and making a whole new frame.  I’ll be using the main part of the Colman tent trailer frame that I was about to use for a new utility trailer.

This ( above photo) is a beefier frame  2″ x 3″ box steel compared to the factory boler frame 1-1/2″ x 2-1/2″ box steel.   As well the bigger frame is bent not cut and welded to the angle for the hitch.  I plan to add a third piece in the middle and have the hitch mounted to that.

I like this frame,  mostly the body mounts.  But I will add a few more pieces..  Adding a little weight here will not matter.. just means no problems down the road.  The original boler design was to have a light frame and use the combination of a fiberglass / plywood sandwich floor to ADD strength to the frame.  So they both need to be in good condition to work.  Over time things would sag..  and weaken.  And that’s the case with the frame under there now.

Yes I crawled under to see what’s up and shoot some photos.  Above is the rear floor.  And sure enough the left side has sagged.  Someone welded a angle brace … but that’s not a fix.  I’m surprised to see no other framing … just the two little beams.

 

And here’s the middle floor .  ( where you stand and walk ) again it seams like no support..  That plywood / fiberglass is very strong !  It does not flex when I walk on it.  And I really doubt that rusty bent piece of angle is doing much.

So looking toward the hitch it’s obvious that the frame was repaired.  Long time ago judging by the rust.  All these problems and the torsion suspension is very much wore out..  That’s why it came home on a trailer.   I know I said I would not be starting this project for a while…  but I’ve got a little spare time and just can’t leave it alone.  I lifted the whole trailer off the ground.

Supporting it with my jack stands.  Interestingly this took the sag out of the frame and show me that the whole back of the body was not tight to the frame anymore.  Wow..

This is the floor under where the dinette cabinet was.  The body is attached to the frame with these screws and washers.  They were pulling out of the frame !  So when I lifted the rear they popped up..  This is NOT how I do things..  Those skinny little screws are most likely rusted and at some point would fail.  That is why my frame will have mounting flanges and carriage bolts to mount the body.

Yes I had some fun removing stuff from the interior.

All the cabinets have to come out anyway..  They need repairs and will be repainted.   May leave the closet alone.. it’s mounted very nicely with cap bolts.   The rust that you see ..  I believe was caused by moisture inside the trailer.. not leaks.  If you close these fiberglass trailers up, then they condensate inside..  best to leave vents and windows open a bit.

Well everything is out..  Real easy to get at the mounting screws now.  It can sit like this till I’m ready to tackle the frame.  I got new suspension on sale..  so that’s another big part of the frame.

These will be joined with heavy angle iron before becoming part of the frame.   For this blog I’m going to divide the work up into three more parts / pages.   Most of my projects have more than one page ..cause I don’t like long posts.   Next page will be the Frame.  Then the Body..  and finally the Interior.

#2 The Frame:

 

70’s Coleman Tent Trailer.

Aug 16 2017:

It was free… and you know how that goes..  It was also broken..  So.. time to make something different from the old girl.   I’ve done it before..  made a nice useful trailer out of a old funky one..  I wish I took a photo of the Coleman before I took it apart.. But I forgot…    So the photos start with a stripped down trailer (frame) ready for some decisions on what to make.

But let’s talk about why I took it apart !

Why not just fix it up..  nope.  where do I start..  How about with the broken lift mechanism.  We had to hook up our portable winch to pull on the four cables that lift the roof.  The treaded block that is pulled along the crank rod was stripped.  And it was easy to see why..  The roof was so heavy from water leaking in and soaking the foam and wood that even our 2000 lb winch needed help.  so we went from corner to corner lifting and blocking … then taking up the slack with the winch ..  till the roof was up.   The roof was a mess.. and the canvas was ripped and things were just bad..  So I stripped the canvas off..  and removed the roof..  that darn thing must of weighed 1000 lbs !  It’s taken me two days to get the Coleman down to just a frame.  A pile of aluminum,  a pile of wood and a pile of steel.   And I’ve gained a few parts..  stove, sink, furnace, power panel with 30 amp cord, roof vent, ice box and two sheets of plywood..

She was big as tent trailers go..  11 ft long.  with the fat 10″ wheels.  and brakes !  All aluminum & steel.

What a great blank canvas for a trailer !  I will need to spend some money though.  new tires / wheels so that I can use the one good one as a spare.  Also a new 2″ hitch,  and treated deck boards should finish it of nice.   I plan to move the rear bumper in so that the deck is 11 ft long.  That balances the trailer better.  And I’ll trim the sides in flush with the wheels..  that makes the width exactly 6 ft.  The plan is to build it similar to the tandem  trailer I build and have been using for a few years now.

Love this trailer..   this has  worked very good.  But for the little guy I will do solid sides with stake pockets so you can add height.  Oh and same height all the way around not raised in the front

For now I have to put this project aside to do other stuff.

Sept 9 2017:

Well I can’t work on the LeSharo till I get the motor hoist back..  So I got the new driveway done..  and now I’m thinking I’ll tackle the new trailer.   I’m off to PA to get two new wheels for it..  I have new lights and a new 2 ”  coupler..  so I can get to work.

I removed some of the crap .. like the propane tank holders, chains and the wiring .  And today I stripped the frame of all the stuff that I don’t need …and some stuff I’ll change

Now I can pick it up..  so I put it up high on the saw horses.  Oh and it’s upside down for a bit till I get a few things done.  First thing is moving some of the cross pieces.  One by one I’m spacing them out more evenly.

The brakes got put on this project .. when I bought a Boler project..   I will need the frame for that..  so.. nothing more to see here..

So see how I use the frame on the Boler !

1986 Winnebago LaSharo Motorhome

I saw this for sale cheap…  and I was only sorta interested..  sorta !

So I threw it out there on the family page.   I did so because many of them were looking at smaller RV’s.  And this is the same size as a long pickup.  but it has a lot of RV stuff in there.  Including two full beds.  So what to do !  I went and had a good look..  the motor runs but knocks so bad you don’t really want to drive it.  The roof leaked at some time and damaged the ceiling panels..  But that’s not a big deal in this RV cause the frame is all steel.  The rest is in good condition for it’s age.  I paid the few hundred bucks and had it towed to Peter’s shop..  The plan is to explore the motor fix later this summer.  Here’s a video ..

These Motorhomes have an endearing following:

And it’s easy to see why.  The four cylinder motor gets very good gas mileage ..  but is under powered for this size vehicle.  It’s front wheel drive , therefor it’s low to the ground… No steps !  In fact it’s the lowest entry of any RV.  The layout inside works very well.. and makes good use of the space.   Here’s a new video that better shows that..

I made the forward bed down just to see how that went..  great bed.  Also I wanted to see how much of a job the ceiling would be..  and it doesn’t look like that big of a deal.   Looks like the factory ceiling was paneling covered with fuzzy headliner stuff..   Ok .. I get that..  but that headliner did not do well with the constant rubbing of peoples heads on it..   Plus it was glued to the paneling..  30 years of rubbing , heat… cold.. nope . did not do good..  I’m thinking just smooth white finish is best.

Aug 2017:

I found a complete drive train for the LS..  running motor … not working transmission..  33,000 miles on it  AND  it’s here in BC .  just a 7 hr drive away..

Update: Aug 2017

After I sold the Empress motor home ,  I had the money to buy the motor from the fella down at the coast..  And how lucky I was that he was coming to Grand Forks to buy a car..  So he delivered the motor ( complete with transmission and front drive).  What a great deal..  Even though there is a few years difference the motors are identical.  

Also as a bit of bonus..  he discovered that the reason for his transmission not working was a broken wire connector.  So I have a spare transmission too.  I will also have both spare ECU’s for the trans & motor.  I could just do a quick swap of the motors.. but I would like to clean up the new motor and replace some of the gaskets..  check the seals and set the valves..  All easier while outside the LS and in the shop.

Aug 10 2017:  The LS is now in my driveway facing the shop door..

Today in the cool morning I have removed the front fascia and bumper..  and sizing things up..   wow there is a lot of hoses to keep track of..  Going to have to lift the front quiet a bit to get under there..

I have the new motor apart from the transmission now…  sure don’t like the right side motor mount..  not enough room to swing a wrench.   Seems every bolt holding the two together is a different length !  curse the French.   And speaking of bolts !  are they metric.. or SAE..  seems a combination of both ?

I was using a 5/8 socket on the motor bolts ..  so I’m confused a bit.  So now to mount the motor to the stand and park the transaxle outside out of the way.

Sept 25 2017:      I had lost the use of the motor hoist for a few weeks and while waiting I got some other things done..  Also needed the new gaskets for the good motor so got them ordered and here.  This week is time to get R done.  The goal was always to get the LaSharo running good before winter sets in.. and then I’ll park it till spring to work on the interior.

My nephew is a mechanic and he will come help with the swap..  He’s done many motor swaps.  My next step is to pull the existing motor out ..  get the two side by side and change over the best parts..   Then I want to power wash the motor compartment.

So after much cursing and sweat..  the motor is out and I washed the whole thing down.  Nicer to work without all the yuck.   Now the good motor needs a bit of work and then in it goes.

The old motor is probably re-buildable …or at least some of the bits are useable..  Need to get it on the motor stand and see…

Here’s the new motor in..  Took 4 hrs and lots of patience.  And that’s just bolting it to the transmission !  now I need to hook up what seams like a hundred things.  It better run… cause this is not an easy in / out sorta thing.

Oct 10 2017:  Thanksgiving !

And I’m thankful that things are moving along with the re- hooking up of motor stuff..  I took a little break and went camping / quading with friends..  But this weekend I’m back at it scratching my head over the hose and wire puzzle.  Got some great help from my Facebook  LeSharo friends..

RUNS !

Yup .. it fired right up..  it’s now the 15 th of Oct.. and I have it all together and the coolant in there too..  I drove it next door and parked it for the winter..  SO will continue with renewed vigor in the spring..   Will start a new page for that..   And now I’ll focus my attention on the boler..

Page Two.

 

 

70’s Terra Jet 453E page5

Continuing with the RE-Assembly:

I’m going to spend another few days before I kick the TJ outside so I can use the shop for servicing tractors..   So let’s se what I can do.

The Chain :

There it is..  The greasy mess.   Well this took most of a day..  got the tension sprocket in the wrong place.  so had to do it all over..  Got it right now..  and everything is smooth.   Also got the brake caliper mounted ..  it fits it’s new home great..

Wheels & Rims:

today I was going to put the wheels back on the TJ..  But as I was looking them over and there was too much I didn’t like..  Two of the tires were very old..  like 40 years !  cracked..  They all had tubes in them.. .so there were other issues.   I decided to pull them all off the rims.  What a job..   rusted on there..  tubes stuck..  yuck.  So what better time to pick the best rims..  clean them up …  paint them and mount the new tires I bought two years ago.

This is the tires I got..   as close to the chevron tread as I could get with out breaking the bank..   Just need to go get them from storage.   And I’ve painted the rims…  black,  BUT  dark steel gray on the outside.. where you see..   classy.

When the paint is good and cured I’ll mount the new tires.  Hopping the bead seals and holds air ..

Rollin Rollin Rollin…

Those are some bad tires ..  but they hold air the way they are suppose too..   and they look good ..

I’m putting the body back on and covering the TJ outside for a bit..

But come on… gota take a photo first.   And just because the TJ goes out of the shop..  does not mean I stop working on the project.  I need to get the motor ready,  The seat ready, the floor panels, roll bar and windshield..   All these things can be done in the shop still.   Sooo lets start another page for the continuing work:

Page 6  Onward to the finish line..
Or back to the start..   page 1

70’s Terra Jet 453E page4

Putting it all together :

And that calls for some new parts !  Bushings & seals for the steering rod.  And new seals for the axle bearings.   That should keep the water out.  And those new bushings will take the slop out of the  steering.

Speaking of that..  I got the steering back in the TJ..   I amaze myself sometimes ..  I got the bracket perfect..  Everything lined up.  My backer plates are working good..  helps to squeeze the tub flat and get a better seal.

The wheel is nice and sturdy too.  All the steering components are from the 76 TJ..  So other bits needed to migrate with them..

Like the brake pedal..  and with it came the parking brake.   That will be nice to have..  And if anyone is asking..  I’m not painting inside the greasy chain run..  to much work.. and it’s protected with the grease.

I’ve been painting the front hubs..  and some other bits..  Got the bearings and seals in the holders ready to go..  Also cleaned up and resealed the chain cover on the transmission.

Just basically getting all the parts ready for re- assembly.  I want a rolling unit by the end of month..  Because I need the shop to earn some money servicing tractors.   But I’m not letting that prevent me from being careful and paying attention to the little things.  Like…

welding washers on the control rods, for better action.

Today we got the axles front and rear back in.   A bit of pushing for the rear one to get it through the transmission and the other obstacles.

The front was easy..  and as you can see the steering is all done.  Just need the rear hubs back on and the wheels could be put back too..  and we roll !   But I’m a bit ahead .. so I’d like to install the chain and maybe the brake.

Things are lining up good.. But I need to cut some of that motor mount away to get the brake disc on..   Also my rear transmission brace worked exactly as planed..

This is a hallmark in the restore..   enough of the TJ is done so it will roll on it’s own wheels. And I can now determine the best placement for the seat.  However  It’s time to start a new page for the finishing touches…  ..

Page 5

Or back to page 1 where it all started

70’s Terra Jet 453E page3

Finishing the Tub…

I used truck box liner finish on the first Terra Jet.. and I liked the results.  It’s a rough finish.. but hey it’s a rough looking tub.

And that’s done..   Reminds me of the first Terra Jet tub. ( below )

Yup.. more or less the same..  Except the frames are welded in the newer ones..  so much heavier to move.   and while the Rhino liner paint is curing..  I set to work doing a few small touches to the bumpers..  plus I installed the side boards that protect the body sides.

Like this winch mount on the front..  It’s upside down ..  so is the tub.  This holds a 2000 lb winch quite nicely.

Also a small improvement to the hitch..  some places to hook to.   Very nice..   It’s the little touches that I like..  Everything got some black paint..  and will be finished off when the tub gets flipped.  I’m trying some new paint..  It’s much like the Por 15 that I like.. but less cost.  So far so good ..

It’s a nice shiny black.. and brushes on smooth.   I’m cleaning and sorting and painting some of the parts..  I’m finding out that between the two Terra Jets there are big differences..  Such as the steering.  I noticed that the steering  from the 76 TJ is offset to one side..  so all the bits are different from the 73 TJ where the steering wheel is in the middle.  Hmm..  I have to be careful.

Even these pedals are slightly different.

One thing leads to another:

So I’m picking and choosing the parts I want to use..  And I’m finding all kinds of compatibility issues.   I want to use one part of the steering from the newer TJ and that means I need to change a bunch of stuff..  and !  I will need to use all the steering parts from that TJ all the way to the wheel hubs..   On top of that ..

The brake pedal , and it’s hanger / cross piece are a bit different to allow for the steering shaft and the park brake to work..

And this bracket ..  for the steering will need to move 2 ” over to the left.   Because the new steering is offset to the left..  Geez !  I’m sorting it out..

Inside the tub:

Lots to do as soon as the paint cures good..   I will need to move that steering bracket,  weld on a center seat support..  and a battery tray.  Also I have to remove the transmission adjustment bracket.  This setup is for a two stroke motor.  It will be in the way of my bigger motor.

This will be changed to the newer style.

This is the new way..  the bracket goes..  to the back wall.  This is also an adjustment for the clutch belt.  And a mount for the clutch brake..  that stops the transmission for changing gears.

Got the inside all cleaned and the steering bracket moved.

The other unnecessary stuff removed..   Above you can see the body seam caulking ..  A little added leak proofing..  and it smooth’s out the sharp edges for painting.   Again I’m going with gray paint..  it’s easier to see leaks and to work on stuff with a lighter color.

PLUS…   It looks good with the black tub.. blue body.   Just need to install a battery holder and modify the motor mount to suit the Honda.   And that leads to the Re- assembly .   And another page !

Continued on ..   PAGE  4

Or..   back to page 1  where it all starts

70’s Terra Jet 453E page2

March 2017:

Rebuilding the TUB

I have a great way of dealing with the bulge of the chain run that plagues the underside of all Terra Jets.   In the case of this one it hangs a further two inches below the bottom at the rear axle.  And that makes it vulnerable to hitting rocks …  and therefore making a hole …that lets the water in !   Can’t have that.  Nope..  And I don’t want to be repairing that after I have gone to this much trouble.  My solution:

Add the two inches right across the back..  and cap it with 1/8 ” plate steel.  Ha ! take that rock !   This also makes a good sump for the bilge pump,  and changes the curve at the rear..  ( stern )

This is just the test fit..  but I’ll be welding these new 3/16 ” thick sides to the frame.

Done..  Also have to think ahead to what will be needed and easier to install now.. like the brake holder.  Two small pieces to stiffen the 1/8 bottom plate too..  and a quick paint job on the underside..  Next…

I tacked the 1/8 th plate into place..  so I could flip the tub over.   and weld up some of the holes..

There was lots of those holes..  It’s a good thing the tub won’t have to win any beauty contests.  But I’m wanting it strong and leak proof not pretty.  Things have to work with the other parts though..  Like the body needs to seal to the top of the tub.

So I’m rebuilding parts like these front corners.  I will test fit the body too..  And other considerations like the fuel tank , the seat and the battery holder.   They all need good mounting .

This is the tank from an Argo..  It’s nice and flat..  but still two inches higher then where the seat was..  Is a higher seat a problem ?  will have to think on this one.  In the mean time I cut the welds ( they were bad anyway) on the seat supports.   I want them bolted through the tub …no welds.  With this setup the tank will be hidden under the seat..  Once things are going together I’ll test out seat locations.

I brought the body in for a test fit..  and to see how things line up.  I’m going to build a winch mount on the front bumper ..and need to know how far back it can go..  And also the sides need to fit in the running boards..   Got it figured out.   Almost all holes are filled in the tub.  Just two more big patches..  and the bottom can go on.

One down.. one to go.  This was a big flap cut into the front ..  Not the tidiest welding.. but strong..   Time to get the bottom done.  lots of careful welding to do.

Well that was NOT easy..  We used straps and blocks to get the bend in the bottom..   That 18 Ga sheet will not bend easy.  The small transition piece had to be heated and hammered into submission.   But it’s done except the curved piece for the back…  I’m thinking a press will be of help there.  And here’s a new short video .. part 2:

I’m taking a few days off to heal up my eye.. got something in there and was finding it hard to see detail..

Back at it..  and I got all the welding done on the tub.

Here we go..  the rear is done.. even have a new drain plug.  The next step is applying the box liner finish..   And it’s time to start another page..

Continued on  Page 3 

Or back to  Page 1 

 

 

70’s Terra Jet 453E page1

Going to build a Keeper :

This is #2.. of the 3 Terra Jets I had.  # 1 was sold over a year ago..  Number 2  & 1 came together as a deal..

Bringing them home..

Number 2 is the one up front on the trailer..   And other than missing it’s body.. it’s very complete and almost in working condition..  ( if the motor ran ).

It would have looked like this one above.. except it was blue.  However it looked like the one below when I rescued it.

There was shreds of the body still clinging to the tub.  Just the head lights left !  I always figured this was the good one of the three..  it rolls , shifts and steers.  And it has the better driveline.   The third Terra Jet  that I picked up from a different person gives me a body for this one.. a great running Honda 20 hp motor, and a lot of good parts.   # 2  here has been sitting in the wings waiting ( two years) for it’s TIME.   Now is the time..   so lets get going:

The first step is always…  bring the project into the shop ..   It’s not quite spring yet .. so I have a bit of time before all the spring stuff happens.. and then I would be too busy to do this project.  I want to note here that I intend to use the best of the two Jets I have..   Whether it be the tubs , transmissions..  or any of the parts.   TJ number two is a 1976 model, with a few extra features that are nice to have.   The third TJ is a 1973, with the body, lots of good parts,  and a good tub / frame with the bottom cut out.

Let’s Start:

But where to begin..  I pulled the wheels off..  and put the TJ up on stands.  Then I got down and had a good look under the TJ..   well I found five cracks and holes..  and the underside looks like it was in WW II ..   So we could be looking at a new bottom, and I’ve done that before..    looks like the frame is welded into this one too..  So..  I need to compare this tub to the one outside #3 TJ..  the bottom is already cut out.. And it’s all in pieces.  This is what number three looks like..

And the tub looks better…  But I still have to take the 76 apart.. I need the transmission no mater which tub I use.   And taking things apart  on something old and rusty is never easy.

The rear axle is the most fun!  It is through the transmission with a long key..  and after all these years ..refuses to let go.  We did get the hubs off with a torch, a puller and a lot of banging.  And so far all the aluminum bearing holders are in great shape.    Now I’ve seen others doing this and cracking the transmission case…  so I’m trying a different way..   by pushing on the transmission final drive where the axle passes through.

I’m using a pipe that slides over the axle and presses on the transmission.  And using the axle nut / washer to pull the axle out.  This is proving to be very difficult.  Finally I had enough and took a big hammer to the axle..  and it came out.  All is good..  So we removed the steering and the front axles … and flipped the tub over to see EXACTLY how bad things were.

VERY BAD..   There was two fiberglass patches.. and a few places where I could just poke a hole with my finger..   Plus it’s bent up bad..  So I’m thinking the tub from the 73 jet is looking better and better…  And the fact that it’s all apart and the bottom cut out is a time saver.  looking like I will have a Frankenstein Terra Jet..   73 and 76 parts.  and Honda power.. new bottom..   yahoo.  Here’s a quick video with a look at the better tub..

Transmission :

I took the time last night to clean the grime off the transmission we just removed.  It had a bit of oil showing on the dipstick.  Also functioned as it should.. So I figured all is good.  Well maybe not !

Once cleaned I discovered that it had been welded to repair some cracks.  so the big question here is dose it leak ?  I will finish cleaning it good and fill the oil up and see.    It’s now 3/4 full of oil..  and no leaks..  The axle seals look like new..  and lots of form-a-gasket was used.   so I’m not taking it apart..  It’s good.  On to other stuff…

The Tub:

I finished stripping all important stuff from the 76 tub.  Even cut the frame out..  And it all got dragged outside.   The tub from the 73 TJ got brought in and flipped over..  And its’ great..

Someone even painted the bottom of the frame !   BONUS !  Plus the metal is in way better condition..   A few patches are needed..

Which you can see in the above photo..  They did not know how to remove the steering and the chain tensioner..  so they cut holes !  Geeze..  oh well I can fix those..  it’s just more welding..

And time for a new page .. Rebuilding the tub

PAGE 2

1987 Dodge Raider 4×4 Page 3

Other things to fix :

Now that the carburetor is changed over and working good..  It’s time to address some of the other things.   And the first and somewhat urgent fix is the exhaust leak at the bottom of the header, where it joins the two into one pipe .  It’s never good to have a leak in the exhaust system.   Plus it can be noisy..  this wasn’t too noisy but you could hear it.   So I thought it was simply the gasket that goes there..   And while trying to get the very rusted nuts off we sheared the studs..  Oh boy now we got a can of worms..  But I looked at it as an opportunity to remove the exhaust manifold and remove some more of the not needed  stuff .  So we pulled the both pieces of the exhaust out.   And this turned out to be a very good thing..  because the leak was not the gasket ..but a crack in the pipe.

The crack is right up against the weld..   That will not do so I welded the crack up and drilled and tapped out the studs… got new studs & nuts..  Also welded shut a hole where the pipe came off for the silly reed valve..  ( pollution control stuff).   The new carb has no place to hook up that stuff.. so it’s doing nothing but taking up space.  Plus it could be another exhaust leak down the road..  When all is done I should have a very quiet Raider.

Isn’t that pretty !   This is going to put the rest of the motor to shame..   You can see my plug for where the pipe was..   Oh and the heat shield will not go back on..  it’s only real purpose was to provide warm air to the air intake..    Again no place for that.

Well I’m all done that job..  and the exhaust is going out the back where it should..  That crosses a few things of the list..   It’s good to drive till the weather is warmer.

Nov 2017:

Well I did get the brakes done,,  And used the Raider for most of the summer..  then I put it up[ for sale..   It’s sold now to someone I know and he wanted a good hunting buggy..  Prefect..   That chapter closed !

1987 Dodge Raider 4×4 Page 2

It’s February… Late February..  And the Carb kit is here !

And this is what I got..  A conversion kit.  I would not say complete, because it’s not..  I’ve had to make some bits and buy some bits.  So I made room in the shop for the Raider to sneak in..   And set to work removing all the crap that the Mikuni carb needed to work..  All the vacuum lines and electric sensors… gone.

This is after I installed the adapter plates for the Weber.   And that was after I plugged some holes.  The old carb had coolant flowing through..  so I had to plug those off.   I got nice little nipples to plug the vacuum manifold.   And I needed to deal with the return vent line from the fuel tank.  I bought a new fuel filter that had the place for that vent line so problem solved.   But there’s more things to figure out.   Despite being told this kit worked for the auto transmission..  there was no way to hook up the kick down cable to the throttle.  I had to invent something ..

A bicycle brake cable with a crimp on terminal..  hey it works!   Took me an hour to figure it out..  But I was determined.

So here’s how it all looks .. that round thingy is a fuel pressure regulator..  adjustable too.   The instructions don’t say much ..but they did say that  fuel pressure needs to be 2.5 psi..  so that is the solution.   One power wire to the choke  and we are off and running…

Test Drive:

WOW..  I can’t believe the power now..   That old carb was a dog.   The Raider is zippy..  and the shifts are good too..  initially the idle was too high. The spring was having trouble pulling the throttle back..  so I tweaked the cables  a bit and got that to work.  The motor idles at 800 rpm like it should now..  So back into the shop to tidy things up and check it all over.

And that is where we are at..  Here’s  the finished install.   I fixed a few other things while the Raider was warm and dry..   The wipers would never park properly. .  So I pulled the motor out and repositioned the drive arm..  fixed !    I also installed the day time running lights that I’ve had for a bit..  last fall I wired the switch up and now we have lights too.

AND.. I made a video of the whole thing…

Time for a new page…

Page 3    Other fixes:

1999 Craftsman GT3000 Tractor Page 2

The Re-assembly / Restore:

If you are here and you didn’t read the first page..   then do that first..    PAGE ONE:

dscn2567-235132042

Let’s keep this photo of a nice one to see how I do..   I will be re-painting the body.. and I’m using what I have on hand.. .and that is the Civic Red that I painted the Suzuki Sidekick last winter.

WP_20160519_002

So it’s a change of color..  a color that Sears would not have used.. but I don’t care..   I like this color.   Anyway..  back to the task at hand..

wp_20161213_002

That means starting with the things that need repairing..  like the steering.   Here’s the steering all fixed with new bushings, greased and painted… good to go.   Hey it’s a start!  And other than the mower deck ..it’s the only thing that really did need a fix.  I took the frame to the car wash and gave it a bath..  It’s now sanded and cleaned and ready for paint.  Going to be nice working on a clean frame.

wp_20161214_002

Well that’s done.. But I don’t want to start messing with it till it’s had a few days to cure good.

Well I’ve painted most of the parts..  and the frame has had a few days to cure good.  In the mean time I’ve been cleaning and draining (all over the floor)  the transaxle.

wp_20161217_001

It’s now back in place.. I need to find a filter to fit, and then refill the oil.  This transaxle has a separate pump from the drive..  and a spin – on filter too.  It’s twice the size of a normal lawn tractor.  The plan here is to get as much back together while upside down.

Jan 2017:

Well I finally got some ambition and I am getting back to this tractor.  Trying to remember how things went together..  And realizing that spring is just around the corner.. I have other important stuff that will need the shop..  and I will need this tractor come spring.

I flipped the frame back right side up..  I’m slowly filling the transaxle with oil..   and the steering is back in.. and working soooo nice.  I have no idea how much oil goes in to the transaxle..  so I’ll just keep filling till it comes out the breather..  Found a new filter.. turns out to be the same one used on the motors.

Got more done today…  motor is in,  the trans is working good..

and a lot of things are fixed and adjusted good..   Next the dash … wiring … and the fuel tank..

April 10 2017:

Finally got back to this tractor..   and a good thing cause the grass is growing..  and the plan is for this to be my main mower.

When I parked it over to one side of the shop.. this is what it looked like.  Rolling with the wiring mostly done..   In the last few days I had time to finish up all the “putting” back together.  Today it looks like this…

All the best parts from the two GT 3000’s . And that included some of the green painted body parts that were is great condition..  So no need for a paint job.  New seat.   Motor serviced.. and today we started it up for the first time in a while..  It runs great..   took it for a spin in the yard and WOW.  !  All the work on the steering paid off…  and this is a pleasure to drive.   The concerns with the transmission are gone..   We are calling it “Big Green Meanie”  It is much bigger than most lawn tractors.   Next the deck needs to be all rebuilt..

April 24 th  2017:

It’s taken a lot of time to get the deck set up with new belts and the one new arbor.  Lining things up..  figuring out which spring goes where.  It was messed up when I got it..  so I needed to get it right again.  There is very close tolerances for the two belts.  The first try I got the wrong size belt from the motor …and it was rubbing on the metal.  Last night I got a shorter belt and that solved all the problems.   Also I had to make a whole new wiring harness.   All the safety circuits were giving me problems ..  So I took everything away except the clutch & PTO interlock for starting.  So yes you could get of the seat while the mower is engaged..   but would you !  if the PTO is just a simple button !  And using the parking brake is a must ..unless you want the tractor to wander off on it’s own.  Just like all the new cars these days ..  they presume you are stupid and should not be allowed to operate a machine.

So here we are..   ready for duty.   and hoping it does ok this summer.

1999 Craftsman GT3000 Tractor

wp_20161207_001

This is what it should look like…

dscn2567-235132042

Not the same one..  but you get the idea.. I always find a photo of the same tractor from a google search to show what it looks like in good condition.

This is the first of many projects for the winter..  This came to me as a package of 2 1/2 tractors..   the others are just for parts..  this one is complete..  and runs.  the 48 inch deck needs work.. and the tractor is a real mess.   Been sitting out under the trees.

wp_20161207_002

Lot’s of great things about this tractor.. the best is this triple blade 48 inch deck.  This is a deluxe deck !  needs an arbor, and a good cleaning..

wp_20161207_005

This is a heavy duty tractor..  large 12 inch rear wheels , hydro transmission,  electric PTO for the deck.  20 hp twin motor..   I like it..   wp_20161207_004

But what a mess..   I’m thinking it’s worth the full treatment..  So First thing we did was run the motor.. yup.. good motor.. smooth.  even the battery charged up ok..   Time to start taking it apart….  The plan is to strip it down to the frame .. repair all the worn out bits, like the steering.  I’m even going to remove the rear axle / hydro unit.

wp_20161211_001

Alrighty.. the motor is out and the very old oil drained.  That’s going to be a happy motor when it gets fresh oil & filter.  I gave the bottom half of the motor a bath while it’s hanging out.   Now all that’s left is a rolling chassis.

wp_20161211_002

Everything is very sturdy for a small tractor.  The hydro unit has a separate pump from the drive.  Interestingly the hydro pump has a horizontal drive while the motor drives vertically for the mower deck.  So the drive belt does a twist..   One of the parts that I need to fix is the steering.  It’s very loose and defiantly worn bad.

wp_20161211_003

Here it is out and in my vise.  I’m disappointed to see that they use those darn nylon bushings for the two shafts.  It does not take long for them to wear out and become sloppy.    I’m going to concede and buy new ones..  at least they lasted more than ten years.  However I could not get a new upper bushing ..so

wp_20161212_001

I made one..  In my hand is the worn plastic one.. I took a 3/4″ nut and drilled it out and added a grease fitting..  Welded in place…   New and improved ! This part of the steering takes all the force of the operator yanking on the steering wheel.   So it needs to be strong.

wp_20161213_001

This is where I’m at..   stripped down to just the frame.   Now starts the cleaning and restoring process..    I’m thinking a new page..  so

PAGE TWO:

1987 Empress MotorHome

Fall 2016 :

Another  “almost free”  RV..

I say almost.. because there is always something that needs money thrown at it.   The “free”  fifth wheel I got a few years back needed the whole roof replaced..   BUT  when you start off at zero dollars , it’s easy to spend a bit to make it right again.

wp_20161123_001

Also I’m working for this one..  I have been and will be putting in hours of work to clean up and help dispose of  “stuff”  for a good customer of mine who is charged with the task of helping her friends who have got to a care home.  That’s the trade for this lovely unit.  Plus they need it gone in order to sell the property.

empress1

This is what we found..   This is a 1987 Tripple E  class C  motorhome.  27 ft Canadian built.  very good quality.   It has been parked there in the yard for 4 years now.  I was told that he started it a year ago.. no proof of that..   When we pulled the cover off the air cleaner I found old rotten sunflower seeds stashed in there..   So Dave & I  jumped it and poured  some gas down the carb.. with a bit of coaxing it started.  So it runs !   there is just 100,000 kms on it so it should be good.  All the batteries are dead.  I have replaced the motor battery, and in the spring I’ll replace the camper battery.

wp_20161111_003

It’s Blue !   a very typical color scheme for that time..   Needs a good cleaning both inside and out.  But it’s overall condition is good..  There are a few repairs to do inside..   just the oak cabinet doors coming apart..  no big deal easy to fix.

The floor plan is interesting..

floorplan

This unit has the twin beds in the back.   And the usual large bed at the front..  plus the dinette makes in to one..  That’s ample sleeping..  The rest is typical and very functional.  This unit also has the shower on the other side of the hallway.  Both bathroom and shower doors open and turn the hallway into a big bathroom.  cool idea !

The Plan:

Well we think we’ll keep it for now..  even though we have a good RV.  This one would be better for short weekend getaways..  Plus we can loan it out for family camping.   For now I’m going to empty out some stuff, test all the systems…then tarp it for the winter..

Testing  1 2 3 ..

The first thing to do was take the deep cell batteries out..  I found the recite for them..  2006.  So they are ten years old..   They are not as dead as I thought..  still had 6 volts in them..  and the water was mostly gone..  so we have topped them up and they are taking a charge now.  I powered the MH up with the 30 amp power plug..  So far all the lights work, the fridge is working too ( that’s a big one). The AC unit fan won’t turn..  wants to . but something is blocking it..  So it’s up to the roof to see what’s up..  and sure nuff…  the wasps and the stink bugs had built a city.   All clean now and the AC works fine.  Tested all the gas appliances today.  everything works as it should.. Value is climbing..

wp_20161125_001

Under the left rear bed is home to the water tank..  and the bus heater.  works just like the dash heater ..  hot coolant provides heat while you are driving ..  great for those “off” season trips.  The water pump is also here..  Very convenient and easy to get to.  However very messy , quite the tangle of wires and water lines.  I don’t like the way they did the drain for the  water tank, but it may have to be there.  One great thing about this vintage of RV is that the plumbing is all above the floor..  most of it you can see.

wp_20161125_003

Here’s one of three cupboard doors that need to be glued back together.   This is not surprising after thirty years.   The list of repairs needed is small..  I’ve ordered the bits needed for the repairs..  new vent covers, a new porch light..  It’s not much.

Now there are some things that are “optional”  repairs.  Like the bathroom sink..

And the blue counter !   SAY WHAT..  who thought this looked good ?   I’ve got a little stainless steel bar sink that would be better in here..  and while I’m at it I’ll replace the counter with something neutral.   As well some of the curtains are faded and looking a bit ratty..  An LED light or two would be nice..

Since I was into all the cupboards and compartments I decided to run antifreeze through the plumbing.  Just to make sure.   I was dismayed when water came out first !  Not good..  and sure nuff there was a leak under the bathroom sink.  The faucet .  These are cheap plastic faucets..  Now for sure I’m installing a new sink ..and faucet.  At lease I’m assured there is antifreeze in the lines now.

As for those batteries.. well they aren’t doing well..  even though they took a charge they are not coming back to full power..  so I’ll recycle them and in the spring I’ll buy a new battery.

A small project:

empress11

See this lamp !  It’s fugly,  It’s loose,  and it has one of those 12 volt bulbs that looks like a 110 volt 40 watt bulb.  ?  Nope..  no good..  I’m rebuilding it with a LED bulb.. no weird bumps, and the switch will be down on the base where you can see it.  But what I’m tempted to do (in the spring) is add a raised part to the back against the wall.  On it would be a 110 volt plug ..  (for an alarm clock ..or what have you)  and two reading lights.   No more lamp.

Hibernation Mode:

wp_20161130_003

The parts came and we had our first snowfall..  but it melted !  So I was able to get the vent lids and Covers installed..  And now the Empress is covered for the winter…  this blog will continue in the spring when I get to work on it.

It’s Spring !   April !

And of coarse the snow is long gone..  and the Empress is on the list of many things to do..  The tarp is off and I bought a new deep cycle battery for it..  Plus new curtains have been ordered for the bedroom.   Time to get to cleaning & repairing.  !

This is the largest battery I could get.  There is room for two.. but they are pricey.. so one for now.

We have spent two days cleaning and I’ve repaired a few things on the list.  The fridge cleaned up great !  no broken parts and it works on power perfectly.  I even fixed the light… with a LED bulb.  The broken cupboard doors have been re- glued …

Everything has been vacuumed and washed.  I also took time to clean out all the outside storage compartments.

Like this generator cabinet.. one of four cubbies.  Cleaned and carpet added.

Even took the time to install a rubber floor in the entrance step.  I’ve ordered a new sink & faucet for the bathroom.  The plumbing is next.

April 24 2017:

I removed the toilet and the bathroom faucet.  hooked up the new faucet, and plugged the toilet line.  Then I pressured up the water lines.. I wanted to confirm where the leaks are..  Turns out to be the toilet valve ( not the tee) .  so I replaced that..  the hot connection to the faucet was leaking too..  easy fix.  And that takes care of the plumbing!  So I removed the vanity top.  and I’m gluing new formica on top.

And the night stand at the same time..  much better (neutral color) .  And so this is what the vanity top looks like..

With the new faucets and I have polished the sink so it looks way better. Ready for installing… which is not easy..  I have to use a mirror to see the screws… and bend my body in ways that hurt…

May 2017 :

Turns out it was easier to put the counter back than take it out..  I repaired all the plumbing leaks and put the bath back together now.

Looks much better.   Remember what I said about free is not really …  well because the Empress was not winterized properly .. I’ve had to replace all the faucets, the toilet valve and a few fittings.   We have replaced the curtains in the bedroom..  They are thicker and make the room better for sleeping.   I have also changed the top of the night stand..  added a few goodies too.

Now we have a LED night light , clock with alarm, a better 110 plug, a voltage meter and a USB charge port.   So now we are good to go..

I still have a few more things to do..  they are outside.  Like re- sealing the roof.  That will be done after we get back from a shake down run this May long weekend.  But I did re seal the hot water tank ..  and clean the remaining moss from the higher surfaces.

The curtains are all back in and clean..  In fact the whole interior has had a wash..  and is smelling so much better.  I have tested all the propane systems ..  and all is good.  The other day I coxed the motor back to life with some gas down the carb.. it’s been idle since October.  The I took it out for a good drive.  After putting in some higher grade fuel..   the motor settled down a bit..  still an exhaust leak up by the motor..  but we can live with a little extra noise.

May Long weekend:

Well we made it 1 1/2 hours up the north fork valley to a rec site for a weekend of R&R..   Everything worked great..  even towed the utility trailer with the quad in it..   Only one thing happened unexpectedly … the window on the door came loose..  So I need to fix that..  We got to try out all the systems.. even the furnace.

What a great time..

July 2017:

So the plan was to sell the Empress after family camping ..  use it there and then Let Go.   How ever just three days before that someone approached me wanting to buy it right away..  so I did..

BYE Bye..